Conductive polymer type SEPC Series　 Large capacitance, Low ESR For print out This is an even lower ESR series based on our SEP series. Suitable for use with motherboards, servers, VGA, etc. Lead free-flow is supoprted.
	Marking : (Purple) Polarity(-), Rated voltage, Rated Capacitance SANYO, OS-CON, Lot.No. SEPC.

Specifications

Items	Conditions	Characteristics
Category temperature range		-55 to +105
Tolerance on rated capacitance	120Hz	M : 20%
Tangent of loss angle	120Hz	Less than or equal to the value of Table3
Leakage current 1	After 2minutes	Less than or equal to the value of Table3
ESR		Less than or equal to the value of Table3
Characteristics of impedance ratio at high temp. and low temp.	Based the value at 100kHz, +20	-55	Z/Z20	0.75 to 1.25
		+105	Z/Z20	0.75 to 1.25
Endurance	105, 2,000h, Rated voltage applied	c/c	Within 20%
		tan	1.5 times or less than an initial standard
		ESR	1.5 times or less than an initial standard
		Leakage current	Below an initial standard
Damp heat (Steady State)	60, 90%RH, 1,000h, No-applied voltage	c/c	Within 20%
		tan	1.5 times or less than an initial standard
		ESR	1.5 times or less than an initial standard
		Leakage current	Below an initial standard (after voltage processing)
Resistance to Soldering heat	Flow method (2605 X 10s)	c/c	Within 5%
		tan	Below an initial standard
		ESR	Below an initial standard
		Leakage curren	Below an initial standard (after voltage processing)

1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 105.


Dimensions

	(unit : mm)
	Size Code D+ 0.5max. Lmax. F d0.05 E9 8.0 9.0 3.50.5 0.6 E12 8.0 12.0 3.50.5 0.6 E13 8.0 13.0 3.50.5 0.6 F13 10.0 13.0 5.00.5 0.6

Size List

RV : Rated voltage (SV) : Surge( room temperature )

RV (SV) F 2.5 (3.3) 4.0 (5.2) 6.3 (8.2) 16.0 (18.4) 270 E12 470 E9,E13 F13 560 E9 E9,E13 680 E13 F13 820 E9,E13 F13 1000 E9 1500 F13 2700 F13

For the minimum packing quantity, see this.

Table 3 SEPC Series Characteristics List

Size Code	Part Number	Rated Voltage (V)	Rated Capacitance (F)	ESR (m)(max.) 100kHz to 300kHz	Rated ripple current (mArms) at105	Tangent of loss angle (max.)	Leakage current (A) (max.)
E9	6SEPC470MX	6.3	470	8	5700	0.1	592
	4SEPC560MX	4	560	7	6100	0.1	500
	2SEPC560MX	2.5	560	8	4700	0.1	280
	2SEPC820MX	2.5	820	7	6100	0.1	500
	2SEPC820MY	2.5	820	5	7200	0.1	500
	2SEPC1000M	2.5	1000	7	6100	0.1	500
E12	16SEPC270M	16	270	11	5000	0.1	864
E13	6SEPC470M	6.3	470	8	5700	0.1	592
	4SEPC560M	4	560	7	6100	0.1	500
	4SEPC680M	4	680	7	6100	0.1	544
	2R5SEPC820M	2.5	820	7	6100	0.1	500
F13	16SEPC470M	16	470	10	6100	0.1	1504
	6SEPC680M	6.3	680	7	6640	0.1	857
	6SEPC1500M	6.3	1500	10	5560	0.1	1890
	4SEPC820M	4	820	7	6640	0.1	656
	2SEPC2700M	2.5	2700	10	5560	0.1	1350

1 Capacitance tolerance : M ; 20%
2 After 2 minutes

Frequency coefficient for ripple current

Frequency 120Hzf<1kHz 1kHzf<10kHz 10kHzf<100kHz 100kHzf<500kHz Coefficient 0.05 0.3 0.7 1